Manual Reset Canon MP145 (Waste ink tank full)

Cara mereset printer mp 145 yg full tank / Waste ink tank full. Tidak perlu menggunakan software untuk meresetnya.

Biasanya di monitor display keluar kode E 27 atau E 5 .

Untuk mengatasinya adalah sebagai berikut :

Cara Reset Printer Canon MP145 dan MP160

Step 1 : Push Power switch by continue (Tekan Power On/Off)

Step 2 : insert plug(Masukan Power, Power Tetap di Tekan)

step 3 : Tekan Tombol Reset 1x, lepaskan Tombol Pwr, Tekan Reset dua kali lagi Sampai Menjadi 0 (tekan tombol tanpa jeda)

Step 4 : Push + display change from 0 to 1 (tekan tombol + untuk merubah 0 ke 1)

Step 5 : Push Power switch again , Printer will be print 1 page(tekan tombol power –> tombol start sampai ngeprint 1 hal.)

step 6 : Open cover (buka tutup printer)

Step 7 : Unplug (cabut kabel power)

Step 8 : Take out ink 40 and 41(lepaskan catridge 40 dan 41)

Step 9 : Insert plug again (pasang kabel power)

Step 10 : Push power switch (tekan tombol power)

Step 11 : Open cover (scan cover) (buka tutup scaner)

Step 12 : Inksert ink 40 , 41 again (masukan catridge 40 dan 41)

berikut ini resep ngereset waste ink counter (error E16 / E27) :

1. Matikan printer (kabel power masih tercolok), tekan dan tahan tombol STOP/RESET kemudian tekan tombol ON/OFF

2. Tahan tombol ON/OFF, tekan tombol STOP/RESET 2x

3. Lepaskan kedua tombol, tunggu sebentar dan printer akan masuk ke SERVICE MODE

4. Printer akan charging

5. Setelah printer selesai charging, tekan tombol STOP/RESET 4x. (Waste ink counter reset)

6. Setiap kali tombol STOP/RESET ditekan, lampu ON/OFF akan berubah warna hijau dan oranye

7. Sesudah itu Matikan printer dengan cara menekan tombol ON/OFF ( sebanyak 3 kali agar printer mati total ) dan cabut kabel POWER

8. Hidupkan kembali printer.

The number of the Reset : button pressing LED Function Remarks

0 time Green Power off

1 time Orange Service pattern print

2 times Green EEPROM print

3 times Orange EEPROM reset

4 times Green Waste ink counter reset

5) Unplug cable power. (for MP145 / MP150)

6) Turn Off Power. (for MP160)

Berikut tanda Error Code/Kode Error :

E2-2 = No paper (ASF)

E3-3 = Paper jam

E4 = No ink

E5-5 = The ink cartridges are not installed or a non-supported ink Cartridge is installed, or the ink cartridges are not installed properly

E8 = Waste ink absorber full, or platen waste ink absorber full

E9 = The connected digital camera / video camera does not support Camera Direct Printing

E14 = The Ink cartridges whose destination are wrong

E15 = Ink cartridge is not installed E16 – Ink remaining is unknown

E16 -E19 = Failed to scan head alignment sheet

E22 = Carriage error

E23 = Paper feed error

E24 = Purge unit error

E25 = ASF(cam) sensor error

E26 = Internal temperature rise error

E27 = Waste ink absorber full or platen waste ink absorber full

E28 = Ink cartridge temperature rise error -

E29 = EEPROM error

E33 = Paper feed position error

E35 15 = USB Host VBUD overcurrent error – USB

E37 17 = Abnormal motor driver error

E40 20 = Other hardware error

E42 22 = Scanner error

atau dgn ini di gabungkan aja n di coba2

RESETER CANON PIXMA MP145

it’s work as same as Canon MP 150 or MP 160,

This is the step :

.

Canon MP145

.

with the printer powered off but connected to a power source , you must:

1. Press stop/reset button, and then press [ON/OFF] button to restart

2. Press [ON/OFF] again and then press twice the stop/reset button.

3. Press [ON/OFF] & Stop/reset button together, this time to enter the repair status and power lights will be green,

4. Press stop/reset button 4x and warning lights will be go out in [ON/OFF]button.

5. Turn off the printer.( it must be turn off) and then turn it on again.

.

Use with your own risk ,

i’ll try this way and my Pixma MP145 not blink again.

.

The number of the Reset button pressing
LED Function Remarks
0 time Green Power off

1 time Orange Service pattern print

2 times Green EEPROM print

3 times Orange EEPROM reset

4 times Green Waste ink counter reset

5 Unplug cable power. (for MP145 / MP150)

6 Turn Off Power. (for MP160)

.

.

Error Code :

======================

E2-2 = No paper (ASF)

E3-3 = Paper jam

E4 = No ink

E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly

E8 = Waste ink absorber full, or platen waste ink absorber full

E9 = The connected digital camera / video camera does not support Camera Direct Printing

E14 = The Ink cartridges whose destination are wrong

E15 = Ink cartridge is not installed

E16 – Ink remaining is unknown

E16 -E19 = Failed to scan head alignment sheet

E22 = Carriage error

E23 = Paper feed error

E24 = Purge unit error

E25 = ASF(cam) sensor error

E26 = Internal temperature rise error

E27 = Waste ink absorber full or platen waste ink absorber full

E28 = Ink cartridge temperature rise error -

E29 = EEPROM error

E33 = Paper feed position error

E35 15 = USB Host VBUD overcurrent error – USB

E37 17 = Abnormal motor driver error

E40 20 = Other hardware error

E42 22 = Scanner error

.

.

TAMBAHAN

==============

ERROR E5

————–
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly

1. Gunakan lap bersih dan lembab usapkan pada connector catrigenya pelan pelan sampai bersih.
Prinsip dasarnya tinta yang mengering atau tinta yang basah atau bahkan kerak yang ada di connector catrige akan mengganggu koneksi antara catrige dan rumah catrige yang berisi pin-pin banyak. sehingga catrige tidak bisa mendeteksi keberadaan catrige dengan sempurna.

.

2. Sedot kembali semua tinta yang ada di catrige dengan sangat pelan pelan sampai habis (di sedot di beberapa sisi sudah tidak ada tinta). gunakan tisu yang di celup air HANGAT (bukan panas) untuk membersihkan head. Baru setelah itu isi kembali tintanya dengan sepertiga isi. jangan sampai terisi separo atau bahkan penuh. Pasang kembali ke rumah catrigenya.

Mengatasi E27

=========================================
1. Biarkan Kabel power tetap terkoneksi ke sumber arus.
(Tdk perlu mencabut kabel power saat printer masih menyala).
2. Tekan dan tahan tombol Stop/Reset.
3. Tekan dan tahan tombol Power (tombol Stop/Reset tetap di tekan)
4. Tetap tekan tombol Power, kemudian lepas tombol Stop/Reset.
5. Tekan tombol Stop/Reset 2x kemudian lepas lepas tombol Power.
” Tunggu sampai angka 0 muncul di display “
6. Tekan tombol Stop/Reset 1x.
7. Tekan tombol Power 1x, printer akan mencetak 1 lembar kertas.
8. Tekan tombol Stop/Reset 2x.
9. Tekan tombol Power 1x, printer akan mecetak 1 lembar kertas
10. Tekan tombol Stop/Reset 3x.
11. Tekan tombol Power 1x. (tidak ada proses pencetakan)
12. Tekan tombol Stop/Reset 4x
13. Tekan tombol Power 1x agak lama & lepas (utk mematikan printer).
” Jika printer tetap tidak bisa dimatikan, cabut kabel power printer “.
14. Nyalakan printer.
15. Pesan error E27 sudah hilang & printer sudah berjalan normal.